Holosun HS507K X2 FrontĪnd just for comparison…let’s see the full-size C model vs the K.
Let’s continue with Holosun’s micro red dot with its K model…the HS507K X2. Now let’s look at some micro red dots for concealed carry handguns. Great chevron reticle with outer ring that helps beginner shooters.Robust build with 20,000 hour battery life, solar backup, and shake awake.We’ve mounted our multiple 507Cs to both Brownells Glock slides, PDP, and more. It also makes it a great option for people that have older-gen RMRs and are looking to modernize. Using the same footprint as the Trijicon RMR, the number of slides that can mount the HS507C without the need for adaptor plates is a huge blessing. And you can actually disable it to save battery life. Once you really get the hang of it…you shouldn’t see the ring anymore. Holosun 507C X2 Primary Arms Vulcan Reticle Holosun 507C X2 Primary Arms Vulcan Reticleīut that’s not all (sorry…couldn’t resist), there’s also a ring on the outside to show you if you’re off center. Lastly…there’s a nice tray that slides out for the battery…meaning you don’t have to take the entire unit off your handgun and lose zero each time you swap the battery.Ĭheck out that nice 10 MOA chevron reticle which draws you to the center. Very handy for setting and forgetting and for saving battery life. The 507C also features “shake-Awake” meaning it has an auto-off feature (you can choose how long it takes for the dot to turn off also!) and will auto-turn on when you move the optic. Holosun 507C X2 Primary Arms Vulcan Solar Panels However, the solar panel does not recharge the battery in any way. There’s also a solar panel on top that gives another source of power for when the optic is in sunlight. Holosun 507C X2 Primary Arms VulcanĪt over 20,000 of battery life, the Holosun 507C is an optic that you will likely never replace the battery on from use…just remember to change it every one to two years. The glass has also been completely scratch-free thus far.īuttons are easy to access and manipulate on the left side.
Vortex viper red dot how to#
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.Ĭlick here to see a video from Vortex on how to install our red dot base on a slide.OG Holosun HS507C on a Brownells Glock 19 slide. This product should be installed and checked by a qualified gunsmith. Modification of your firearm may nullify the manufacturer's warranty. The screws that are included with this mount require a 5/64'' allen wrench for installation. Apply blue Loctite to the provided mounting screwsĢ Button Head Cap Screws - Provided for Vortex Viper and Venom SightsĢ Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Place the red dot sight on the EGW Sight Mount Install the EGW Sight Mount on the slide Sig Sauer P322 Optics Ready (Need to remove the recoil lug to work) You can take our mount off and replace your rear sight at any time. Simply remove the sight plate on your gun and replace it with our mount in order to mount your Vortex Viper, Vortex Venom, Burris FastFire, or Docter red-dot sight. The EGW red dot sight mount adapter plates for the Sig Sauer P365 Optics Ready pistols are meant to be installed in place of the factory mounting plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins. These dots may not fit properly on the posts on the plate. Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. *All ADE mounts require 6-32 x 3/8" screws. 5 x 8mm Flat Head Screws - for mounting the plate to the slide - Requires use of 2mm Hex Key
Vortex viper red dot driver#
(2) 6-32 x 3/8" Flat Head Screws - Requires 5/64 Wrench or Driver (2) 6-32 x 5/16" Button Head Screws - Requires 5/64 Wrench or Driver
0 kommentar(er)
